StoreDeal.ai store
Shop
  • Deals
  • Deal checker
  • Black Friday
  • Buying guides
  • Brands
  • Stores
Travel
  • Flight deals
  • Hotel deals
Company
  • Research
  • Press
  • Use in AI assistants
  • Contact
  • deal.ai apps
Black Friday 2026
  • Walmart
  • Best Buy
  • Target
  • TVs
  • Laptops
  • Headphones
  • Apple
  • Gaming
  • Vacuums
  • Kitchen
  • Toys
  • Smartwatches
  • Tablets
  • Furniture
  • Mattresses
© Deal.ai Inc.·2222 Ponce de Leon Blvd, Miami, FL 33134·support@deal.ai
TermsPrivacy
Deal.ai
B
Bosch GCM12SD/GCM12GDL Dust Collection Throat Plate Gen 2

Bosch GCM12SD/GCM12GDL Dust Collection Throat Plate Gen 2

4.7(18 ratings)

Best price now

$57.00at Inspire WoodcraftChecked Nov 13

Prices are checked against each store and labelled with when.

Visit Inspire Woodcraft

Ask our agent about this product

It checks today's price at every store, compares the alternatives and answers in about a minute.

Enter to send, Shift+Enter for a new line

Price facts

  • Last seen at $57.00 at Inspire Woodcraft on Nov 13.

Our take on the Bosch GCM12SD/GCM12GDL Dust Collection Throat Plate Gen 2

This is a two-piece zero-clearance throat plate for the Bosch GCM12SD and GCM12GDL glide miter saws. It replaces the factory plate and adds an underside shroud that pushes debris to a rear vacuum port, so dust that normally falls below the table gets pulled away instead. The zero-clearance opening supports material right up to the cut line, which reduces tear-out and keeps small offcuts from dropping under the plate where they can be ejected. It suits owners of these saws who want cleaner cuts and less cleanup, and it installs with the factory screws.

Best forBosch GCM12SD and GCM12GDL ownersTrim and finish carpenters cutting small moldingsShops with a dust collector or shop vacuum at the sawCutting brittle or splinter-prone material
Pros
  • Zero-clearance opening supports material up to the cut line
  • Underside shroud routes debris to a rear vacuum port
  • Two-piece design replaces the factory plate using factory screws
  • Vacuum port comes preinstalled on the rear section
  • Reduces tear-out and offcut ejection under the table
Cons
  • Only fits the GCM12SD and GCM12GDL, not other miter saws
  • Needs a vacuum or dust collector connected to work
  • Zero-clearance slot closes up as the blade bevels or miters
  • Two pieces must be seated correctly to sit flush

Bosch GCM12SD/GCM12GDL Dust Collection Throat Plate Gen 2 prices at every store

  • Inspire WoodcraftNew

    In stockReturn policy

    $57.00Checked Nov 13
    Visit Inspire Woodcraft

What reviewers say

  • 4.7 / 518 ratings

Rated 4.7 out of 5 from 18 ratings. Owners report better dust capture than the factory plate and a straightforward install.

What people mention
  • Dust collectionPraisedOwners say it captures dust the factory plate lets fall below the table.
  • InstallPraisedBuyers report it goes on quickly using the factory screws.
  • Cut qualityPraisedThe zero-clearance opening is credited with cleaner cuts and less tear-out.
  • Zero-clearance slotMixedThe narrow slot must be recut after changing bevel or miter angles.

About the Bosch GCM12SD/GCM12GDL Dust Collection Throat Plate Gen 2

This is a dust collection throat plate for the Bosch GCM12SD and GCM12GDL miter saws. It is a second-generation design with improved dust collection efficiency and faster installation. It is 3D printed from PETG filament.

The plate comes as two solid pieces with no opening. Once you cut into it, the opening is only as wide as the blade (zero-clearance). This supports the material right up to the cut line, which helps prevent tear-out and keeps small offcuts from falling beneath the plate. A shroud on the underside traps debris that would normally be pushed under the plate and sends it to the rear, where it is evacuated through a vacuum port.

The plate is meant to be used with an aftermarket behind-the-blade dust collector, which handles debris from the back half of the blade while the plate captures what comes off the front. It is not designed to be a primary source of dust collection. It is not intended for bevel cuts, which will destroy the shroud and the zero-clearance function. Miter cuts of the full range can be made as long as the blade is at 90 degrees to the table.

Compatibility
Bosch GCM12SD and GCM12GDL miter saws only; not tested on other makes or models
Model number
Found on the top side of the saw's motor housing
Material
3D printed PETG
Throat plate
Two pieces (front and rear sections) with five sets of holes to fit older and newer saws
Installation
Replaces the factory throat plate and reuses the factory screws
Vacuum port
Mounts on the rear section with four preinstalled small screws
Hose
Clear vinyl hose, 1/2" outside diameter
Vacuum side inlet
Accepts 2-1/2" dust collection hose, 2-1/2" shop vacuum hose, 1-7/8" shop vacuum hose or 36 mm Festool antistatic hose
Tool side ports

Questions and answers

Which saws does this throat plate fit?
It fits the Bosch GCM12SD and GCM12GDL glide miter saws. It does not fit other miter saw models.
What is included?
A front and rear throat plate section, a vacuum port with four preinstalled screws, and a clear vinyl hose that carries dust away.
Do I need a vacuum to use it?
Yes. The shroud pushes debris to the rear port, and the hose connects to a shop vacuum or dust collector to evacuate it.
How does zero-clearance help my cuts?
The opening is only as wide as the blade, so material is supported right up to the cut line. That reduces tear-out and keeps small offcuts from falling under the plate.
Will the slot stay zero-clearance when I bevel?
No. Changing the bevel or miter angle cuts a wider path, so the slot opens up and needs recutting for zero-clearance again.
How does it install?
It replaces the factory throat plate and reuses the factory screws. The vacuum port is already attached to the rear section.
Where is the Bosch GCM12SD/GCM12GDL Dust Collection Throat Plate Gen 2 cheapest?
At Inspire Woodcraft, for $57.00, as of our latest check.
What do buyers say about the Bosch GCM12SD/GCM12GDL Dust Collection Throat Plate Gen 2?
Rated 4.7 out of 5 from 18 ratings.
One for a 1-5/8" hose cuff from an aftermarket behind-the-blade unit; one for the supplied 1/2" OD vinyl hose or a 5/8" ID hose (not included)
Fittings
Tapered for a secure connection to many hose brands
Cut limits
Not for bevel cuts; blade must be plumb (90 degrees to the table)
In the box
Throat plate/shroud (front and rear sections), vacuum port, clear vinyl hose, vacuum adapter
Not included
Behind-the-blade dust collector, 5/8" ID hose