StoreDeal.ai store
Shop
  • Deals
  • Deal checker
  • Black Friday
  • Buying guides
  • Brands
  • Stores
Travel
  • Flight deals
  • Hotel deals
Company
  • Research
  • Press
  • Use in AI assistants
  • Contact
  • deal.ai apps
Black Friday 2026
  • Walmart
  • Best Buy
  • Target
  • TVs
  • Laptops
  • Headphones
  • Apple
  • Gaming
  • Vacuums
  • Kitchen
  • Toys
  • Smartwatches
  • Tablets
  • Furniture
  • Mattresses
© Deal.ai Inc.·2222 Ponce de Leon Blvd, Miami, FL 33134·support@deal.ai
TermsPrivacy
Deal.ai
S
Stereo 2.8W Class D Audio Amplifier - I2C Control AGC - TPA2016

Stereo 2.8W Class D Audio Amplifier - I2C Control AGC - TPA2016

4.7(3 ratings)

Best price now

$10.52at The Pi HutChecked 3 h ago

Prices are checked against each store and labelled with when.

Finding cheaper alternatives

Checking the Deal.ai store…

Price facts

  • Lowest price today: $10.52 at The Pi Hut (checked Nov 20, 2026).
  • $10.52at The Pi HutChecked 3 h ago
    Visit The Pi Hut

    Our take on the Stereo 2.8W Class D Audio Amplifier - I2C Control AGC - TPA2016

    This is a tiny stereo Class D amplifier board built around the TI TPA2016 chip. It delivers 2 x 2.8W into 4-ohm speakers at 10% THD and runs from 2.7V to 5.5V, so it suits battery-powered and portable builds. Its two distinguishing features are an I2C control interface and automatic gain control that holds the signal back from clipping. Compared with basic LM386 amps it is far more efficient and louder for its size, but it expects a microcontroller to get the most from it.

    Best forPortable and battery-powered audio projectsMakers upgrading from an LM386 ampMicrocontroller builds that can drive I2CSmall speakers in 4-ohm or 8-ohm builds
    Pros
    • Stereo 2 x 2.8W output from a very small board
    • Class D efficiency, about 89% into 8 ohms at 1.5W
    • AGC keeps loud passages from clipping
    • I2C lets you set gain and AGC from a microcontroller
    • Runs from a wide 2.7V-5.5V supply
    • Built-in thermal and over-current protection
    Cons
    • Settings are not stored, so gain and AGC must be set at every power-up
    • Default 6dB gain and AGC are a compromise without I2C
    • Differential inputs need R- and L- tied to ground for single-ended sources
    • Bridge-tied outputs cannot share a common ground
    • PWM output means speaker wiring and layout matter

    Stereo 2.8W Class D Audio Amplifier - I2C Control AGC - TPA2016 prices at every store

    • The Pi HutNew

      In stockShips from the UK · priced in GBP (£8.00) · duties may applyReturn policy

      $10.52Checked 3 h ago
      Visit The Pi Hut

    About the Stereo 2.8W Class D Audio Amplifier - I2C Control AGC - TPA2016

    A mini class D with AGC and I2C control? Yes please! This incredibly small stereo amplifier is surprisingly powerful. It can deliver 2 x 2.8W channels into 4-ohm impedance speakers (@ 10% THD) and it has an i2c control interface as well as an AGC (automatic gain control) system to keep your audio from clipping or distorting.

    If you don't want to use I2C to control it, it does start up with 6dB gain by default and the AGC is set up for most music playing. We do suggest using it with a microcontroller to configure it, however, since it's quite powerful. Settings are not stored in the chip, so you'll need to adjust any gain & AGC amplification settings every time the amp is powered up.

    Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC. Since the amp is a class D, it's incredibly efficient (89% efficient when driving an 8Ω speaker at 1.5 watts) - making it perfect for portable and battery-powered projects. It has built-in thermal and over-current protection but we could barely tell if it got hot. This board is a welcome upgrade to basic "LM386" amps!

    The inputs of the amplifier go through 1.0uF capacitors, so they are fully 'differential' - if you don't have differential outputs, simply tie the R- and L- to the ground. The outputs are "Bridge Tied" - which means they connect directly to the outputs, with no connection to the ground. The output is a ~300KHz square wave PWM that is then 'averaged out' by the speaker coil - the high frequencies are not heard. All the above means that you can't connect the output to another amplifier, it should drive the speakers directly.

    Comes with a fully assembled and tested breakout board with 1.0uF input capacitors. We also include 3.5mm screw-terminal blocks so you can easily attach/detach your speakers, and some header in case you want to plug it into a breadboard . Speakers are not included, use any 4-ohm or 8-ohm impedance speakers.

    Our awesome tutorial and Arduino library will let you set the AGC configuration (you can also just turn it off), max gain, and turn on/off the left & right channels all over I2C! You will be ready to rock in 20 minutes!

    Note: The terminal blocks included with your product may be blue or black.

    Speakers, cables, breadboard and Arduino board are NOT included

    Revision History

    As of August 19th, 2024 – we've updated this PCB with Adafruit Pinguin to make a lovely and legible silkscreen - you may get the new PCB or the older version with vector fonts - both are identical other than the fancy silkscreen.

    Specifications

    • Output Power: 2.8W at 4Ω, 10% THD, 1.7W at 8Ω, 10% THD, with 5V Supply

    • PSRR: 80 dB, 5ms startup time

    • Designed for use without an output filter, when wires are kept at under 2"-4" long

    • I2C interface pins for setting gain, AGC configuration parameters, etc. See our tutorial for more details

    • Selectable gain from -28dB to 30dB

    • Excellent click-and-pop suppression

    • Thermal shutdown protection

    • Shutdown pin for power saving mode.

    • Low current draw: 3.5mA quiescent and 0.2uA in shutdown mode

    • Dimensions (without 0.1" header): 22mm x 28mm

    • Weight: 2g

    Resources

    • Tutorial and Downloads

    Ask our agent about this product

    It checks today's price at every store, compares the alternatives and answers in about a minute.

    Enter to send, Shift+Enter for a new line

    Questions and answers

    Do I need a microcontroller to use it?
    No. It starts up at 6dB gain with AGC set for typical music, so it plays out of the box. A microcontroller over I2C is recommended to set gain and AGC properly.
    Does it remember my gain settings?
    No. The chip does not store settings, so any gain and AGC changes must be sent again each time the amp powers up.
    How do I connect a normal single-ended audio source?
    The inputs are differential and pass through 1.0uF capacitors. Tie R- and L- to ground and feed your left and right signals to L+ and R+.
    Can I use 8-ohm speakers?
    Yes. The 2.8W per channel figure is into 4 ohms at 10% THD; into 8 ohms you get less power but higher efficiency, around 89% at 1.5W.
    Can the speaker outputs share a ground?
    No. The outputs are bridge-tied, so each speaker connects across its two output pins and neither side goes to ground.
    What supply voltage does it need?
    Anything from 2.7V to 5.5V DC, which makes it easy to run from a battery pack or a 5V rail.
    Where is the Stereo 2.8W Class D Audio Amplifier - I2C Control AGC - TPA2016 cheapest?
    At The Pi Hut, for $10.52, as of our latest check.
    What do buyers say about the Stereo 2.8W Class D Audio Amplifier - I2C Control AGC - TPA2016?
    Rated 4.7 out of 5 from 3 ratings.