Will it fit a standard drill?

Yes. The shank is 3/8 inch (9.6mm), which fits most corded and cordless drills with a standard chuck. Use the lowest speed setting.

Can I drill a hole for a faucet in tile?

Yes. The 45mm diameter matches common faucet and pipe openings, and the 1 inch depth covers typical wall tile. Mark the spot, start at an angle to bite the glaze, then straighten up.

Do I need water while drilling?

It is not required, but water or another coolant is recommended. It keeps the diamond rim cool, reduces dust and extends the bit's life.

What materials can it cut?

Ceramic and porcelain tile, glass and glass bottles, marble, stone, concrete, plastic and gypsum board. It is not meant for wood or metal.

The cutting depth is 25mm (1 inch). For thicker material, drill from both sides or work in steps.

One diamond hole saw. No pilot bit, guide or tape is included, so plan on using tape and a steady hand to start the hole.

Where is the Uxcell 1 Pcs 1-3/4 Inch(45mm) Diamond Hole Saw cheapest?

At Walmart, for $11.99, as of our latest check.

Uxcell 1 Pcs 1-3/4 Inch(45mm) Diamond Hole Saw

Best price now

$11.99at WalmartChecked Nov 9

Prices are checked against each store and labelled with when.

Visit Walmart

Uxcell 1 Pcs 1-3/4 Inch(45mm) Diamond Hole Saw

Best price now

$11.99at WalmartChecked Nov 9

Prices are checked against each store and labelled with when.

Visit Walmart

Ask our agent about this product

It checks today's price at every store, compares the alternatives and answers in about a minute.

Price facts

Last seen at $11.99 at Walmart on Nov 9.

Our take on the Uxcell 1 Pcs 1-3/4 Inch(45mm) Diamond Hole Saw

The Uxcell 45mm diamond hole saw is a single coated core bit for drilling clean holes in tile, glass, marble, stone, concrete and similar hard, brittle materials. It has a 45mm (1-3/4 inch) cutting diameter, a 3/8 inch shank and a 1 inch cutting depth, with a diamond abrasive coating on the rim and a rust-resistant coating on the body. It is a low-speed, wet-or-dry bit: run it slowly with a reciprocating motion and add water to keep the diamonds cool and the bit lasting. It suits one-off jobs like a faucet or pipe hole in tile; dedicated tile bits with wax-filled cores or continuous rims cut faster and last longer on repeated work.

Best forCutting faucet and pipe holes in wall tileDrilling glass bottles, jars and sheet glassHoles in marble, granite and stone countertopsOccasional DIY use on concrete or gypsum board

Pros

Diamond-coated rim cuts hard, brittle materials cleanly
45mm size fits common faucet and pipe openings
3/8 inch shank fits most standard drills
1 inch cutting depth handles typical tile and stone thickness
Rust-resistant coating and inter-tooth gaps help clear chips
Works wet or dry, with water recommended for longer life

Cons

Single bit only; no pilot bit or guide included
Needs slow speed and steady hand; wandering is easy on smooth tile
Diamond coating wears out faster than pro-grade bits on repeated use
Cutting depth of 1 inch limits thick slabs
Water cooling is advised, which means managing slurry

Uxcell 1 Pcs 1-3/4 Inch(45mm) Diamond Hole Saw prices at every store

WalmartNew
In stockSold by Tasharina CorpReturns: Sold by a Walmart Marketplace seller; returns go to the seller under the seller's returns policy.
$11.99Free shippingChecked Nov 9
Visit Walmart

About the Uxcell 1 Pcs 1-3/4 Inch(45mm) Diamond Hole Saw

This diamond hole saw cuts 45 mm (1-3/4 inch) holes in hard and brittle materials. It works on ceramics, tiles, stone, glass bottles, concrete, glass, marble, plastics and gypsum board, and leaves smooth, clean holes.

The saw uses ultra-fine diamond abrasive grains with a thickened diamond coating on the top. Clearance between the teeth reduces cutting resistance and helps clear chips. A colored anti-rust coating reduces friction and resists corrosion, which lowers cutting heat.

To use it, apply cross-shaped transparent tape at the drilling location and mark the center with a pen. Drill with a low-speed reciprocating motion. Water or another coolant can be added during drilling to extend the life of the bit.

Diameter: 45 mm / 1-3/4 inch
Shank diameter: 9.6 mm / 3/8 inch
Cutting depth: 25 mm / 1 inch
Mesh count: 50/60
Materials: Ceramics, tiles, stone, glass bottles, concrete, glass, marble, plastics, gypsum board
Coating: Diamond coating with anti-rust finish
In the box: 1 x diamond hole saw

Specifications

size: 1-3/4 InchSource

Questions and answers

Will it fit a standard drill?: Yes. The shank is 3/8 inch (9.6mm), which fits most corded and cordless drills with a standard chuck. Use the lowest speed setting.
Can I drill a hole for a faucet in tile?: Yes. The 45mm diameter matches common faucet and pipe openings, and the 1 inch depth covers typical wall tile. Mark the spot, start at an angle to bite the glaze, then straighten up.
Do I need water while drilling?: It is not required, but water or another coolant is recommended. It keeps the diamond rim cool, reduces dust and extends the bit's life.
What materials can it cut?: Ceramic and porcelain tile, glass and glass bottles, marble, stone, concrete, plastic and gypsum board. It is not meant for wood or metal.
How deep can it cut?: The cutting depth is 25mm (1 inch). For thicker material, drill from both sides or work in steps.
What is in the box?: One diamond hole saw. No pilot bit, guide or tape is included, so plan on using tape and a steady hand to start the hole.
Where is the Uxcell 1 Pcs 1-3/4 Inch(45mm) Diamond Hole Saw cheapest?: At Walmart, for $11.99, as of our latest check.