Is the DWE7491RS good for cutting hardwoods?

Yes. The 15 amp motor and 10-inch blade rip through hardwoods, and the fence holds alignment under load. Depth of cut is 3-1/8 inches at 90 degrees and 2-1/4 inches at 45.

How does it compare with the DeWalt DWE7485?

The DWE7491RS has a larger 32-1/2 inch rip capacity and a rolling stand, while the DWE7485 is smaller and lighter with a shorter rip capacity. The 7491RS suits wide sheet goods and trim; the 7485 suits tighter spaces and lighter transport.

Does it come with a stand?

Yes. It ships with a rolling stand, push stick, miter gauge, blade guard, riving knife, wrenches and a cord wrap, and the saw stores these onboard.

Can one person set it up?

The rolling stand folds and unfolds by one person, but the saw itself is heavy to lift into a vehicle. Plan for two people when loading it.

What is the maximum rip width?

32-1/2 inches with the telescoping fence rails extended. The rails retract for a smaller package when the saw is stored or moved.

Does it accept a dado stack?

The saw is built around a standard 10-inch blade and its guard and riving knife. Check the arbor and throat plate setup before planning dado cuts.

What do buyers say about the DEWALT 10-in. Jobsite Table Saw and Rolling Stand?

Rated 5 out of 5 from 4 ratings.

Where can I buy the DEWALT 10-in. Jobsite Table Saw and Rolling Stand?

2 stores we checked sell it, including Shell Lumber and Hardware, Gap Power.

DEWALT 10-in. Jobsite Table Saw and Rolling Stand

Q: Where is the DEWALT 10-in. Jobsite Table Saw and Rolling Stand cheapest?

At Shell Lumber and Hardware, for $731.73, as of our latest check.

Best price now

$731.73at Shell Lumber and HardwareChecked Nov 10

Prices are checked against each store and labelled with when.

Visit Shell Lumber and Hardware

Ask our agent about this product

It checks today's price at every store, compares the alternatives and answers in about a minute.

What reviewers say

Owners and reviewers rate the DWE7491RS highly for its fence accuracy, rip capacity and stable rolling stand. Many call it one of the best jobsite saws for trim work. Common complaints are weight, the stock blade and mediocre dust collection.

What people mention

Fence accuracyPraisedOwners say the rack-and-pinion fence adjusts smoothly and holds square cut after cut.
PortabilityMixedThe rolling stand sets up fast, but owners find the saw heavy to lift in and out of a truck.
Rip capacityPraisedReviewers value the 32-1/2 inch capacity for shelving and wide trim.
Dust collectionCriticisedUsers report the dust port and shroud leave a lot of sawdust on the table and floor.
Stock bladeCriticisedOwners say the included blade is fine for rough cuts but needs upgrading for finish work.
Stand stabilityPraisedReviewers describe the rolling stand as stable once locked and easy to fold.

About the DEWALT 10-in. Jobsite Table Saw and Rolling Stand

This DeWalt DWE7491RS is a 10-inch corded jobsite table saw that comes with a rolling stand. Its 15 amp motor is built to rip hardwoods, and the 32-1/2" rip capacity handles larger shelving and trim materials.

The rack and pinion telescoping fence system makes fence adjustments fast, smooth and accurate. The fence rails retract to make a small, portable package. A flip-over ripping fence and a patented material support allow narrow rip cuts. Guarding components adjust without tools.

The 21-7/8" x 26-3/8" table supports the material being cut. The rolling stand is designed for easy setup and breakdown. An onboard storage system holds the blade guard assembly, fence, riving knife, miter gauge, wrenches, push stick and cord wrap when not in use.

Blade

10 in, 24-tooth carbide, 5/8 in arbor, centered

Motor

15 amp, 120 V, single-phase, corded

Max speed

4800 RPM

Rip capacity

32-1/2 in right, 24 in left

Depth of cut

3-1/8 in at 90°, 2-1/4 in at 45°

Bevel

Table tilts 45° left