Superior WXS2016 16" Freestanding Wood-Burning Stove
A 1.52 cu. ft. firebrick-lined firebox rated at 55,600 BTU/hr on cord wood, with maximum burn times of 6 to 8 hours. The Superior WXS2016 is an EPA-certified non-catalytic freestanding wood stove — 1.7 g/hr certified emissions, 72% HHV efficiency at low burn — that heats with no electrical connection at all: a natural-draft fire on a 6" chimney, a steel door with ceramic glass, and an air wash that keeps the view of the fire clear. Superior rates it for 700 to 1,400 square feet, as an approximation. from $1,949.
Choose the WXS2016 if you want real wood heat for a small to mid-size space and a heater that keeps working when the power is out — there is nothing to plug in unless you add the blower. It is the smaller, lower-priced of the two Merit Series stoves, and it fits alcove installations.
It is not right if there is no route for a vertical 6" chimney — this is a natural-draft stove that needs roughly 12 feet minimum of effective draw and a termination above the roofline — or if you are counting on it as your only heat source: Superior designs it as a supplemental heater. With no chimney path, a direct-vent gas fireplace such as the Superior DRT3000 series vents straight out a wall instead. And if the space runs past its 700-1,400 sq. ft. rating, step up to the WXS2021.
Specifications
Set the stove on noncombustible floor protection at least 3/8" thick that runs beneath it and extends 16" in front of and 8" to either side of the door opening. Wall clearances are charted for three connector types — single wall, single wall with a UL-listed pipe shield, and double wall — for parallel and corner installations; the double-wall set is the tightest and is the one rated for mobile homes. Alcoves need 48" of width with single-wall pipe, 44" with double wall, and no more than 48" of depth. The chimney is 6": minimum 24 MSG black steel connector into a UL 103 HT Class A factory-built chimney or a code-approved masonry flue, with about 12 feet minimum of effective draw, terminating 3 feet above the roof penetration and 2 feet above any roof within 10 feet. Built to UL 1482 / ULC S627 and HUD standards, PFS TECO report 14-186.
How the WXS2016 compares to the WXS2021
Same Merit Series pedestal stove design, one size apart. The WXS2016 runs a 1.52 cu. ft. firebox, 55,600 BTU/hr on cord wood, 6-8 hour burns and a steel door at from $1,949; the WXS2021 steps up to a 2.0 cu. ft. firebox, 76,000 BTU/hr, 7-9 hour burns and a cast-iron door at from $2,339. Match the stove to the space — this one is rated for 700 to 1,400 square feet.
Features
• EPA-certified non-catalytic wood stove — 1.7 g/hr certified particulate emissions under the 2020 standards
• 55,600 BTU/hr on cord wood, with maximum burn times of 6 to 8 hours on a full load
• 1.52 cu. ft. firebrick-lined firebox that takes logs up to 18" (16" recommended)
• Air wash keeps a flow of air over the inside of the glass to slow build-up
• Black steel door with 5 mm ceramic glass, on a black pedestal base
• Listed for residential, alcove and manufactured (mobile) home installations
Answers to common questions
What chimney does it need, and is any of it included? None of the chimney ships with the stove — it is all configured to your roof. The WXS2016 connects with minimum 6" diameter, 24 MSG black steel connector pipe (single wall, single wall with a UL-listed shield, or double wall) to a UL 103 HT Class A factory-built chimney or a code-approved masonry flue with liner, with connector and chimney from the same brand — Security Chimneys, Jakes Evans/GSW, Dura-Vent, Metal Fab, Ameri-Tec, Metalbestos, ICC and IHP Snap Pak are the approved brands. Plan roughly 12 feet minimum of effective draw, and terminate 3 feet above the roof penetration and 2 feet above any roof within 10 feet. Send us your ceiling height and roof pitch and we will size the run with you.
What has to go on the floor under it? Noncombustible floor protection at least 3/8" thick, extending beneath the whole stove and — in the USA — 16" in front of the door opening and 8" to either side of it. If any connector pipe runs horizontally over the floor, the protection also has to cover under the pipe plus 2" to either side. The stove must not sit closer to combustible walls than the clearance table allows for your pipe type.
Can it go in a mobile or manufactured home? Yes — the WXS2016 is approved for manufactured (mobile) home installation. Mobile homes add four requirements: the outside air kit, double-wall connector pipe with a spark arrestor at the chimney termination, the stove secured to the floor and grounded to the chassis, and never in a sleeping room. Alcove installations are listed too — 44" to 48" minimum width depending on pipe, 48" maximum depth.
Does it need electricity? No — the stove is a natural-draft wood burner with no electrical connection, so it keeps heating through a power outage. The one electric component is the optional Dial-A-Temp blower, which
