What kind of cutting is this blade for?

General-purpose wood cutting: construction lumber, softwood, hardwood, plywood, chipboard and laminate. The 24 teeth favor speed and chip clearance over a smooth finish.

It fits saws that take a 10-inch blade with a 5/8-inch arbor, including most 10-inch miter saws, jobsite saws and table saws. Check your saw's diameter and arbor before mounting.

Does it work on cordless saws?

Yes, it runs on corded or cordless circular saws. It is not a thin-kerf blade, so a battery saw will draw more power than with a thin-kerf model.

Will it leave a smooth finish?

No. A 24-tooth blade leaves a rougher edge and can tear out plywood or laminate. Use a higher tooth count for trim and finish cuts.

Can it cut laminate or melamine cleanly?

It can cut them, but expect chipping and tear-out. Tape the cut line or use a fine-tooth blade for visible edges.

Hyper Tough Circular Saw Blade, 10 in, 24 Carbide-Tipped Teeth, 5/8 in Arbor

Best price now

$12.94at WalmartChecked Nov 10

Prices are checked against each store and labelled with when.

Visit Walmart

Hyper Tough Circular Saw Blade, 10 in, 24 Carbide-Tipped Teeth, 5/8 in Arbor

Best price now

$12.94at WalmartChecked Nov 10

Prices are checked against each store and labelled with when.

Visit Walmart

Ask our agent about this product

It checks today's price at every store, compares the alternatives and answers in about a minute.

Price facts

Last seen at $12.94 at Walmart on Nov 10.

Our take on the Hyper Tough Circular Saw Blade, 10 in, 24 Carbide-Tipped Teeth, 5/8 in Arbor

A 10-inch, 24-tooth carbide-tipped blade for general-purpose wood cutting. The low tooth count and deep gullets clear chips fast, so it suits ripping and rough crosscuts in construction lumber, plywood and softwood more than fine trim work. It mounts on a 5/8-inch arbor and fits most 10-inch miter saws, jobsite saws and table saws. Against finer 60- to 80-tooth blades it cuts faster and cheaper but leaves a rougher edge and more tear-out on laminate and veneered plywood.

Best forFraming and construction lumberRipping and rough crosscutsJobsite and table saws with a 5/8-inch arborHomeowners replacing a worn general-purpose blade

Pros

24 carbide teeth stay sharp through nails-free lumber and plywood
Low tooth count clears chips quickly for fast ripping
Fits most 10-inch miter, jobsite and table saws with a 5/8-inch arbor
Works on corded and cordless saws
General-purpose tooth geometry handles softwood, hardwood and chipboard

Cons

Rough cut finish; not for trim, veneer or laminate
Tear-out on plywood and melamine is likely
Not a thin-kerf blade, so cordless saws work harder
Carbide tips can chip if the blade hits fasteners or grit

Hyper Tough Circular Saw Blade, 10 in, 24 Carbide-Tipped Teeth, 5/8 in Arbor prices at every store

WalmartNew
In stock
$12.94Checked Nov 10
Visit Walmart

What reviewers say

4.4 / 538 ratings

Rated 4.4 out of 5 from 38 ratings. Buyers treat it as a workhorse blade for framing and rough cuts and note it cuts cleanly enough for that job; complaints center on finish quality on finer material.

What people mention

Cut speedPraisedBuyers say the 24-tooth design rips through framing lumber and plywood fast.
Cut finishCriticisedReviewers report a rough edge and tear-out on finish work and laminated sheet goods.
DurabilityPraisedOwners say the carbide teeth hold up through regular home and workshop cutting.
FitPraisedBuyers report it mounts on common 10-inch saws with a 5/8-inch arbor.

About the Hyper Tough Circular Saw Blade, 10 in, 24 Carbide-Tipped Teeth, 5/8 in Arbor

This is a 10-inch general-purpose circular saw blade for everyday wood cutting. It has 24 carbide-tipped teeth and a 5/8-inch arbor.

It cuts construction lumber, hardwood, softwood, plywood, chipboard, and laminate. It works with corded or cordless circular saws and fits the majority of 10-inch miter saws, jobsite saws, and table saws.

The 5/8-inch arbor sets the mounting fit. Check your saw's arbor and diameter requirements before use.

Diameter: 10 in
Teeth: 24, carbide-tipped
Arbor: 5/8 in
Use: General-purpose wood cutting
Materials: Construction lumber, hardwood, softwood, plywood, chipboard, laminate
Compatibility: Corded and cordless circular saws; most 10-inch miter saws, jobsite saws, and table saws

Specifications

size: 10"Source

Questions and answers

What kind of cutting is this blade for?: General-purpose wood cutting: construction lumber, softwood, hardwood, plywood, chipboard and laminate. The 24 teeth favor speed and chip clearance over a smooth finish.
Will it fit my saw?: It fits saws that take a 10-inch blade with a 5/8-inch arbor, including most 10-inch miter saws, jobsite saws and table saws. Check your saw's diameter and arbor before mounting.
Does it work on cordless saws?: Yes, it runs on corded or cordless circular saws. It is not a thin-kerf blade, so a battery saw will draw more power than with a thin-kerf model.
Will it leave a smooth finish?: No. A 24-tooth blade leaves a rougher edge and can tear out plywood or laminate. Use a higher tooth count for trim and finish cuts.
Can it cut laminate or melamine cleanly?: It can cut them, but expect chipping and tear-out. Tape the cut line or use a fine-tooth blade for visible edges.
Where is the Hyper Tough Circular Saw Blade, 10 in, 24 Carbide-Tipped Teeth, 5/8 in Arbor cheapest?: At Walmart, for $12.94, as of our latest check.
What do buyers say about the Hyper Tough Circular Saw Blade, 10 in, 24 Carbide-Tipped Teeth, 5/8 in Arbor?: Rated 4.4 out of 5 from 38 ratings.