Is eSUN PETG good for beginners?

It is manageable if you have printed PLA before. Expect to slow down, raise the nozzle temperature and tune retraction to control stringing.

How is PETG different from PLA?

PETG is tougher, more heat-resistant and more weather-resistant than PLA. PLA is stiffer and easier to print with sharp detail.

How is it different from ABS?

PETG warps far less and does not need an enclosed printer, but it is less heat-resistant than ABS and more prone to stringing.

What nozzle and bed temperatures does it need?

Most users print it around 230–250 °C at the nozzle and 70–80 °C on the bed. Start at the higher end for strength and lower it if stringing appears.

Does it work with a stock 1.75 mm printer?

Yes. It runs on standard 1.75 mm direct-drive and Bowden setups; a hardened nozzle is not required, but a slightly larger nozzle gap helps with oozing.

One 1 kg (2.2 lb) spool of 1.75 mm PETG in a vacuum-sealed bag with a desiccant pack. No nozzle or accessories are included.

Where is the eSUN PETG Filament 1.75mm 1kg cheapest?

At Amazon, for $11.99, 25% under what the other stores charge, as of our latest check.

Where can I buy the eSUN PETG Filament 1.75mm 1kg?

6 stores we checked sell it, including eBay, eSUN Official Store, WoodArtSupply, Newegg.com, esun3dstore-com.myshopify.com.

eSUN PETG Filament 1.75mm 1kg

Best price now

$11.99at AmazonChecked 1 h ago

25% under what the other stores charge

Compared across 6 stores. Prices are checked against each store and labelled with when. As an Amazon Associate, Deal.ai earns from qualifying purchases.

Visit Amazon

Ask our agent about this product

It checks today's price at every store, compares the alternatives and answers in about a minute.

What reviewers say

Owners of eSUN PETG mostly praise consistent diameter, tidy winding and strong, well-bonded prints. Complaints center on stringing, oozing and bed adhesion that is sometimes too strong, plus the tuning PETG always demands.

What people mention

StringingCriticisedOwners report stringing and fine wisps between parts unless retraction and temperature are dialed in.
Print strengthPraisedParts are described as tough and impact-resistant, with layers that hold together well.
WindingPraisedThe spool is reported as evenly wound with no tangles or overlaps during long prints.
Bed adhesionMixedFirst layers stick reliably, but some users say prints can fuse to smooth PEI or glass and need a release agent.
DiameterPraisedMeasured filament stays close to 1.75 mm, giving steady extrusion and few clogs.
TuningMixedIt prints reliably once settings are adjusted, but users say it is less forgiving than PLA out of the box.

About the eSUN PETG Filament 1.75mm 1kg

This is a 1.75 mm PETG filament for 3D printers, supplied as a 1 kg (2.2 lbs) spool. PETG combines features of PLA and ABS: it has the toughness and mechanical properties of ABS, and it is easy to print with minimal warping like PLA. The color is solid black.

The filament has a dimensional accuracy of +/- 0.05 mm. It is made for low warping, good layer bonding, less stringing, and no bubbles or cracking. The spool holds 350-355 m of filament, wound to resist overlapping and tangling, and it is made to feed smoothly without clogging the nozzle or extruder.

Printed parts have good clarity, light transmission and high gloss. They are waterproof and tough, with good impact resistance, mechanical strength, weather resistance and chemical resistance. Typical uses include toys, cosmetic containers, electronic accessories and stationery.

Material

PETG

Diameter

1.75 mm

Tolerance

+/- 0.05 mm

Net weight

1 kg (2.2 lbs)

Length

350-355 m

Color

Solid black